Inline Dimmer Cord Switch - Leviton Brand Full Range Lamp Dimmer, Rotary Knob, Feed Trhu
Brown or Ivory (Beige), Great with Cloth Wire - 2-wire cords only!!!!
Leviton Inline switches are durable and dependable, and are the top of the line as far as dimmer switches are concerned. What sets them apart? 1) Smooth function: steady increases and decrease of the light optput. 2) Full range: these will get your bulb as low and as high is it is capable of. 3) Consistent output: cheap dimmers are known for flickering and flashing, especially with today's higher efficiency bulbs. As long as your bulb is marked as "dimmable" (and of course, any incandescent filament), these dimmers will work beautifully. 4) Longevity: Look inside the dimmer, there's a lot going on in there! Don't wast time with cheap dimmers that will fail or fry up in a short period of time.
All of our Edison bulbs (LED and incandescent) are fully compatible with these dimmers. They look great on dimmers, being able to watch the filaments rise and fall with the turn of the knob, and you get only the amount of light you need, when you need it.
Dimmer function: Yes these will also turn the bulb on and off! Rotation starts in the "off" position, as you turn it clockwise it clicks "on", and then you have the ability to rotate the dial to your desired brightness level.
Feed through switches are easy to work with: The shell unscrews with 2 screws. Your cord (make sure you have no power going to it!) will have 2 wires, the "neutral" wire will bypass the switch, just run it along the space in the bottom. Cut your "hot" wire in half, strip your ends (we recommend a small piece of electrical tape when using our cloth wire), and attach one end of your "hot" wire to one screw terminal, and attach the other end to the other.
This listing is for the Leviton Dimmer switch only (a quantity of 1 = 1 switch!!! Wire shown as an example, can be purchased separately!!!)
Showing reviews 1-10 of 14 | Next
Posted by D.P. on Jan 7th 2021
Easy to install and worked as advertised. Perfect for my application
Posted by Unknown on Jan 5th 2021
No soldering required. I had it spliced and running in less than 10 minutes. Only downside was that there was too little room to run the other wire inside the switch case so it looks a little ghetto.
SHV REPLY: Hello, glad it's working for you, regarding the other wire, what size cord are you using? These should be able to fit almost any 18 gauge 2-wire lamp cord, twisted or parallel style (but round cord, 3-wire cord, or thicker gauge cord may make it more difficult)
Posted by Alan Ravage on Dec 24th 2020
I'm sure it was new, in a never opened package and it worked just fine, but I'm not sure it is still commercially available. That is why I'm grateful that it was still to be found. I installed it where it was needed, and it works just as I expected it to.
It arrived sooner than I expected, carefully wrapped. Good seller.
Posted by Unknown on Dec 22nd 2020
Can hardly find these anywhere else. Great for a vintage hanging lamp. Easy to install.
Posted by Unknown on Dec 11th 2020
Service from Snakehead was first-rate. I would definitely purchase from them again.
The dimmer switch is fine. Comes with clear directions for installation.
Works well with a dimmable LED bulb.
Posted by Tom Lutz on Dec 4th 2020
Dimmer was easy to install and worked fine with my LED rope light fixture. Couldn't find one at any ACE or Home Depot stores so glad I found Snake Head.
Posted by Tom W on Nov 25th 2020
Great dimmer switch. We were happily surprised at the full range of dimming capability. It came quickly and was easy to install.
Posted by stephen van eynde on Jul 5th 2020
The product is great & the packaging was the same :)
Posted by Paul Downing on Jun 23rd 2020
Works like a champ, very easy to install.
Posted by Tony Mac on Jun 23rd 2020
Can't say enough good things about the product and the quick service by Snake Head Vintage. Considering it was a modest purchase, they delivered as advertised. Good company to do business with...
Showing reviews 1-10 of 14 | Next